Ducted Fume Hoods

Laboratory Exhaust Solutions for Hazardous Fumes,
Vapors, Gases & Particulates

Reliable Laboratory Containment

Air Science® ducted fume hoods provide personnel protection by drawing laboratory air into a negative-pressure work zone and exhausting contaminated air through the facility’s ductwork.

Available in a range of configurations, our ducted fume hoods support applications involving hazardous fumes, vapors, gases and particulates. From compact laboratory work to high-clearance equipment and traditional sliding-sash installations, each solution is designed to meet specific laboratory and facility requirements.

IMPORTANT

Ducted fume hoods must be properly connected to a facility exhaust system and commissioned to provide the required containment. Hood selection, exhaust volume, duct design, make-up air and discharge location should all be reviewed to ensure the system meets the application’s requirements.

How Does a Ducted Fume Hood Work?

Room air enters through the hood opening and moves across the work surface, creating a negative-pressure work zone. Contaminated air is drawn into the hood’s exhaust path and carried through facility ductwork for discharge outside the building.

The facility exhaust system maintains the required airflow. Exhaust fan selection, duct resistance, sash position and make-up air can all affect containment performance.

When Is a Ductless Fume Hood a Good Choice?

A ductless fume hood can be a good choice for applications involving known chemicals that can be effectively captured by the selected filter media.

Ductless fume hoods can be appropriate for processes that generate relatively controlled quantities of hazardous vapors.

A ductless system can be a good option for laboratories where installing external ductwork is difficult or expensive.

Ductless fume hoods can provide greater flexibility for facilities that may need to relocate equipment. Because filtered air is recirculated back into the laboratory rather than exhausted outdoors, they can also reduce the loss of conditioned laboratory air.

When Should a Ducted Fume Hood Be Considered?

A ducted fume hood may be more appropriate for applications involving high chemical volumes.

Ducted systems may be more appropriate for processes involving unknown or frequently changing chemical mixtures.

A ducted fume hood should be considered for processes that cannot be adequately controlled by available filter media.

A ducted solution may be appropriate when direct exhaust to the outdoors is required by the facility’s risk assessment, applicable standards, codes or procedures.

Explore Our Ducted Fume Hoods

Facility Exhaust
& Installation

A ducted fume hood is one component of a complete laboratory exhaust system. Proper installation requires suitable ductwork, an exhaust fan and appropriate exterior discharge, along with consideration for the conditioned air removed from the laboratory.

Requirement
Exhaust Requirements
Confirm the required exhaust volume and static pressure for the selected hood.
Ductwork & Fan
Size the ductwork and exhaust fan for the complete installed system.
Make-Up Air
Provide sufficient replacement air to prevent excessive laboratory depressurization.
Exterior Discharge
Position exhaust outlets to minimize the potential for contaminants to re-enter the building.
Commissioning
Verify airflow before routine use and recheck performance after system changes.

IMPORTANT

Do not select an exhaust fan or size facility ductwork using a generic rule of thumb. Final exhaust requirements depend on the selected hood, duct length and fittings, system resistance, required face velocity and facility design.

Frequently Asked Questions

Below are answers to our frequently asked questions and links to additional helpful information.

A ducted fume hood is a ventilated laboratory enclosure that draws air into the work zone and exhausts contaminated air outside through a facility duct system. It helps protect personnel from hazardous fumes, vapors, gases and particulates.

Ducted fume hoods exhaust contaminated air outside through facility ductwork. Ductless fume hoods use filtration to capture suitable contaminants before returning filtered air to the laboratory. The right choice depends on the chemicals, quantities, frequency of use and facility requirements.

Ducted fume hoods are often appropriate for higher-volume chemical use, frequent or continuous processes, toxic gases and applications involving chemicals that are not suitable for recirculating filtration.

Not necessarily. Both can provide appropriate protection when properly selected, installed and operated. Safety depends on the chemicals being used, the application and the performance of the complete ventilation system.

Ducted fume hoods generally exhaust contaminated air outside rather than filtering and recirculating it. Any additional filtration or exhaust treatment requirements depend on the application and facility.

Yes. A ducted fume hood must be connected to a suitable facility exhaust system. Ductwork, exhaust fan requirements and exterior discharge must be evaluated for the selected hood and installation.

Face velocity is the speed of air entering the hood opening. It is one factor in containment performance, along with sash position, room airflow, equipment placement and the overall exhaust system.

Make-up air replaces the room air removed by the exhaust system. Adequate make-up air helps maintain laboratory air balance and supports proper fume hood operation.

Relocating a ducted fume hood requires evaluation of the new facility exhaust connection, airflow requirements and installation conditions. The hood should be recommissioned before routine use.

Consider the chemicals and processes involved, equipment dimensions, required work area and facility exhaust capabilities. Air Science can help review your application and identify an appropriate ducted fume hood solution.

Not Sure Which Ducted Fume Hood Is Right for You?

Air Science can help you select the right ducted fume hood based on your chemical applications, equipment requirements and facility exhaust capabilities.